|
 |
15-75 - Onsrud Cutter CNC Router Bits - Three Edge CNC Dor-Bits - Usage: Metal Clad or Fiberglass Doors
(D) = Metal Doors |
 |
18-00 - Onsrud Cutter CNC Router Bits - Single Edge Straight Pilot - Usage: Wood panels, vinyl coated panels, wall board, and aluminum layered materials
(CM/DW) = Construction Material |
 |
20-10 - Onsrud Cutter CNC Router Bits - Single Edge Drywall Bit - Usage: Drywall cut outs
(CM/DW) = Construction Material |
 |
27-00 - Onsrud Cutter CNC Router Bits - Single Edge Laminate Trim - Usage: Trimming laminate counter tops and trimming plastic parts
(LW) = Laminated and Veneered |
 |
27-50 - Onsrud Cutter CNC Router Bits - Double Edge Laminate Trim - Usage: Trimming laminate counter tops and trimming plastic parts
(LW) = Laminated and Veneered |
 |
28-20 - Onsrud Cutter CNC Router Bits - Double Bearing Plastic Trim - Usage: Trimming stacked sheets plastic and laminates
(SP) = SoftPlastic
(HP) = HardPlastic |
 |
28-50 - Onsrud Cutter CNC Router Bits - Flush Trim - Usage: Natural wood, wood composites
(LW) = Laminated and Veneered
(SW) = Softwood
(HW) = Hardwood
(CW) = Composite Wood |
 |
29-50 - Onsrud Cutter CNC Router Bits - Double Edge Chamfer - Usage: Natural wood and wood composites
(SW) = Softwood
(HW) = Hardwood
(CW) = Composite Wood |
 |
34-000 - Onsrud Cutter CNC Router Bits - Aircraft Panel Tools - Usage: Composites
(CP) = Composites |
 |
36-00 - Onsrud Cutter CNC Router Bits - Double Edge Dovetail - Usage: Natural wood and wood composites
(SW) = Softwood
(HW) = Hardwood
(CW) = Composite Wood
(MT/DT) = Mortising and Dovetailing |
 |
37-00 - Onsrud Cutter CNC Router Bits - Engraving Tools - Usage: Wood, plastic, aluminum, and solid surface
(SW) = Softwood
(HW) = Hardwood
(SP) = Soft Plastic
(HP) = Hard Plastic
(A) = Aluminum
(SSP) = Solid Surface |
|
37-20 - Onsrud Cutter CNC Router Bits - Engraving Tools - Usage: Wood, plastic, aluminum, and solid surface
(SW) = Softwood
(HW) = Hardwood
(SP) = Soft Plastic
(HP) = Hard Plastic
(A) = Aluminum
(SSP) = Solid Surface |
 |
37-50 - Onsrud Cutter CNC Router Bits - Double Edge V Bottom - Usage: Plastic,solid surface, composites, laminated and veneer
(SW) = Softwood
(HW) = Hardwood
(CW) = Composite Wood
(SP) = Soft Plastic
(HP) = Hard Plastic
(SSP) = Solid Surface
(LW) = Laminated and Veneer |
|
37-60 - Onsrud Cutter CNC Router Bits - Double Edge V Bottom - Usage: Plastic,solid surface, composites, laminated and veneer
(SW) = Softwood
(HW) = Hardwood
(CW) = Composite Wood
(SP) = Soft Plastic
(HP) = Hard Plastic
(SSP) = Solid Surface
(LW) = Laminated and Veneer |
 |
37-70 - Onsrud Cutter CNC Router Bits - Double Edge Folding Tool for Dibond/Alucobond - Usage: Aluminum/Plastic Sandwich material
(A) = Aluminum |
 |
37-80 - Onsrud Cutter CNC Router Bits - Double Edge Lettering Bits - Usage: Wood
(SW) = Softwood
(HW) = Hardwood
(CW) = Composite Wood |
 |
40-50 - Onsrud Cutter CNC Router Bits - Double Edge Round and Rout - Usage: Natural wood, wood composites, plastic and solid surface
(SW) = Softwood
(HW) = Hardwood
(CW) = Composite Wood
(SP) = Soft Plastic
(HP) = Hard Plastic
(SSP) = Solid Surface
|
 |
40-550 - Onsrud Cutter CNC Router Bits - Four Edge Upcut Spiral Foam Cutters - Usage: Foam Boards
(FP) = Foam |
 |
42-00 - Onsrud Cutter CNC Router Bits - Carbide Tipped Corner Round - Usage: Natural wood, wood composites, and solid surface
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Woods
(SSP) = Solid Surface
|
 |
47-00 - Onsrud Cutter CNC Router Bits - Carbide Tipped - Bead Profile - Stile Bits - Usage: MDF
(CW) = Composite Woods |
|
47-00 - Onsrud Cutter CNC Router Bits - Carbide Tipped - Cove Profile Stile Bits - Usage: MDF
(CW) = Composite Woods |
|
47-00 - Onsrud Cutter CNC Router Bits - Carbide Tipped - Ogee Profile Stile Bits - Usage: MDF
(CW) = Composite Woods |
|
47-00 - Onsrud Cutter CNC Router Bits - Carbide Tipped - Straight Profile Stile Bits - Usage: MDF
(CW) = Composite Woods |
|
47-00 - Onsrud Cutter CNC Router Bits - Carbide Tipped - Traditional Profile Stile Bits - Usage: MDF
(CW) = Composite Woods |
 |
52-550 - Onsrud Cutter CNC Router Bits - Double Edge Foam Cutters - Usage: Foam
(FP) = Foam Products |
 |
66-000 - Onsrud Cutter CNC Router Bits - Single Edge Straight O Flute Edge Rounding - Usage: Edge rounding of parts
(SSP) = Solid Surface
(HP) = Hard Plastic
(SP) = Soft Plastic |
 |
66-001 - Onsrud Cutter CNC Router Bits - Single Edge Spiral O-Flute Edge Rounder - Usage: Edge rounding of parts
(SSP) = Solid Surface
(HP) = Hard Plastic
(SP) = Soft Plastic |
 |
66-002 - Onsrud Cutter CNC Router Bits - Double Edge Straight O Flute Edge Rounder - Usage: Edge rounding of parts
(SSP) = Solid Surface
(HP) = Hard Plastic
(SP) = Soft Plastic |
|
66-003 - Onsrud Cutter CNC Router Bits - Double Edge Straight O Flute Edge Rounding - Usage: Edge rounding of parts
(SSP) = Solid Surface
(HP) = Hard Plastic
(SP) = Soft Plastic |
 |
66-004 - Onsrud Cutter CNC Router Bits - Double Edge Straight V Flute - Usage: Edge rounding of parts
(SSP) = Solid Surface
(HP) = Hard Plastic
(SP) = Soft Plastic |
 |
66-200 - Onsrud Cutter CNC Router Bits - Double Edge Rout and Chamfer - Designed to provide up to a 1/16" top face chamfer and a finished side edge on plastic sheets or parts. |
 |
66-300 - Onsrud Cutter CNC Router Bits - Double Edge Upcut Bottom Surfacing - Usage: Bottom Surfacing for Plastic and Aluminum
(HP) = Hard Plastic
(SP) = Soft Plastic |
 |
67-000 - Onsrud Cutter CNC Router Bits - Fiberglass Router - Usage: Fiberglass and Phenolic
(CP) = Composite Plastics |
|
67-001 - Onsrud Cutter CNC Router Bits - Fiberglass Router Medium Burr W/end Mill Point - Usage: Fiberglass and Phenolic
(CP) = Composite Plastics |
 |
67-002 - Onsrud Cutter CNC Router Bits - Fiberglass Router Medium Burr W/Plunge Point - Usage: Fiberglass and Phenolic
(CP) = Composite Plastics |
 |
67-003 - Onsrud Cutter CNC Router Bits - Fiberglass Router Medium Burr W/Plunge Point - Usage: Fiberglass and Phenolic
(CP) = Composite Plastics |
|
67-004 - Onsrud Cutter CNC Router Bits - Fiberglass Router 2 Flute Burr - Usage: Fiberglass and Phenolic
(CP) = Composite Plastics |
|
67-005 - Onsrud Cutter CNC Router Bits - Fiberglass Router 2 Flute Burr - Usage: Fiberglass and Phenolic
(CP) = Composite Plastics |
|
67-006 - Onsrud Cutter CNC Router Bits - Fiberglass Router Aramid Tool - Usage: Fiberglass and Phenolic
(CP) = Composite Plastics |
|
67-007 - Onsrud Cutter CNC Router Bits - Fiberglass Router Aramid Tool - Usage: Fiberglass and Phenolic
(CP) = Composite Plastics |
 |
67-400 - Onsrud Cutter CNC Router Bits - Un-Ruffer - Usage: Composite panels
(CP) = Composite Plastic |
 |
67-500 - Onsrud Cutter CNC Router Bits - Solid Carbide CG Tool (Carbon Graphite) - Usage: Carbon Graphite, Aramid, Composite Sheets
(CP) = Composite Plastic |
 |
67-600 - Onsrud Cutter CNC Router Bits - Solid Carbide FMR (Fiber Metal Router) - Usage: Carbon Graphite, Aramid, Composite Sheets
(CP) = Composite Plastic |
 |
68-000 - Onsrud Cutter CNC Router Bits - Double Edge PCD Tipped Tooling - Usage: Composite panels and Fiberglass
(CP) = Composite Plastic |
|
68-001 - Onsrud Cutter CNC Router Bits - Double Edge PCD Tipped Tooling - Usage: Composite panels and Fiberglass
(CP) = Composite Plastic |
 |
68-200 - Onsrud Cutter CNC Router Bits - Double Edge PCD SERF Cutter - Usage: Composites
(CP) = Composite Plastics |
 |
70-100 - Onsrud Cutter CNC Router Bits - Saw and Arbor Soft Plastic Slow Feed - Usage: Hard and Soft Plastics
(HP) = Hard Plastics
(SP) = Soft Plastics |
|
70-101 - Onsrud Cutter CNC Router Bits - Saw and Arbor Hard Plastic Fast Feed - Usage: Hard and Soft Plastics
(HP) = Hard Plastics
(SP) = Soft Plastics |
|
70-102 - Onsrud Cutter CNC Router Bits - Saw and Arbor Soft Plastic Fast Feed - Usage: Hard and Soft Plastics
(HP) = Hard Plastics
(SP) = Soft Plastics |
|
70-103 - Onsrud Cutter CNC Router Bits - Saw Arbor - Usage: Hard and Soft Plastics
(HP) = Hard Plastics
(SP) = Soft Plastics |
 |
70-200 - Onsrud Cutter CNC Router Bits - Saw Flush Mount - Usage: Hard and Soft Plastics
(HP) = Hard Plastics
(SP) = Soft Plastics |
 |
70-300 - Onsrud Cutter CNC Router Bits - Saw Flush Mount - Usage: Hard and Soft Plastics
(HP) = Hard Plastics
(SP) = Soft Plastics |
 |
77-000 - Onsrud Cutter CNC Router Bits - Single Edge Top Loading Router Bit Plastic - Usage: Plastic and aluminum
(SP) = Soft Plastics
(HP) = Hard Plastics
(A) = Aluminum |
 |
77-025 - Onsrud Cutter CNC Router Bits - Single Edge Top Loading Router Bit Aluminum - Usage: Wood, Plastic, and aluminum
(SW) = Soft Wood
(HW) = Hard Wood
(SP) = Soft Plastics
(HP) = Hard Plastics
(A) = Aluminum |
|
77-100 - Onsrud Cutter CNC Router Bits - Double or Three Edge Taper Tools - Usage: Wood, Plastic, and aluminum
(SW) = Soft Wood
(HW) = Hard Wood
(SP) = Soft Plastics
(HP) = Hard Plastics
(A) = Aluminum |
 |
80-000 - Onsrud Cutter CNC Router Bits - Taper Pin Router - Usage: Aluminum and non-abrasive hard plastics
(A) = Aluminum |
 |
81-000 - Onsrud Cutter CNC Router Bits - Double Edge Lo Helix - Usage: Aluminum
(A) = Aluminum |
 |
81-100 - Onsrud Cutter CNC Router Bits - Spiral Extrusion Cutters - Usage: Extrusion and sheet aluminum. Optimized for use on multi-head extrusion mills CNC mills and routers
(A) = Aluminum |
 |
81-200 - Onsrud Cutter CNC Router Bits - Double Edge Spiral Cutters - Usage: Aluminum slabs or plates, thin walled structures and supports
(A) = Aluminum |
 |
81-500 - Onsrud Cutter CNC Router Bits - Double Edge Spiral Cutters - Usage: Aluminum slabs or plates, thin walled structures and supports
(A) = Aluminum |
 |
90-00 - Onsrud Cutter CNC Router Bits - T-slot - Usage: Natural wood and Wood composites
(HW) = Hard Wood
(SW) = Soft Wood
(CW) = Composite Wood |
 |
91-000 - Onsrud Cutter CNC Router Bits - Spoilboard Surfacing Cutters - Usage: Aluminum, Plastics and Composite Woods
(HP) = Hard Plastic
(SP) = Soft Plastics
(A) = Aluminum
(CW) = Composite Wood |
 |
91-100 - Onsrud Cutter CNC Router Bits - Spoilboard Surfacing Cutters - Usage: Aluminum, Plastics and Composite Woods
(HP) = Hard Plastic
(SP) = Soft Plastics
(A) = Aluminum
(CW) = Composite Wood |
|
91-120 - Onsrud Cutter CNC Router Bits - Spoilboard Surfacing Cutter Inserts - |
